Custom Turret Tape

Less Searching. More Shooting.

When you're transitioning between barricades, acquiring targets, reading the wind, and navigating mirage, remembering your elevation drops can be challenging. Whether you're competing, hunting, or simply plinking steel, Turret Tape helps take the guesswork out of dialing your elevation.

See Your Numbers. Dial with Confidence.

With large, high-contrast elevation markings printed directly on your scope's turret, spend less time searching for data on your phone, DOPE card, or Kestrel and more time focused on the target.

Traditional etched scope turrets can be difficult to read quickly. Multiple rotations of MIL references, small numbers, and faded markings can slow you down when focus matters most.

Turret Tape features large, easy-to-read numbers designed to make identifying your elevation references faster and easier. Markings are calculated to correspond with the intended adjustment values of compatible scope turrets.

High-Contrast Numbers and Click Markings

Large, easy-to-read numbers and clearly defined click markings make your elevation references easier to identify at a glance.

Precision-Cut to Fit

Each sticker is designed around your turret's diameter, height, and adjustment specifications for accurate marking placement and spacing.

Removable, Repositionable Adhesive

Our proprietary, non-permanent adhesive is designed to remove cleanly without marring your scope's finish or leaving residue. With proper care, stickers can typically be removed and reapplied a few times.

Write, Update, Repeat

The coated vinyl surface allows you to add custom markings with a compatible permanent or erasable marker. Update your notes and drop data as needed.

Built-In Bullet Drop Data

Optional bullet drop data for selected popular calibers and ammunition loads can be incorporated into your sticker for convenient elevation references at a glance.

Optional Red Zone Markings

Our red zone markings provide a visual reference around calculated drop values to help you evaluate potential variations caused by changing atmospheric conditions, ammunition, and other factors. Always verify your actual trajectory and elevation data for your specific setup.

Need a sticker designed specifically for your scope and caliber? We can create a custom Turret Tape sticker based on your turret dimensions, adjustment specifications, and desired drop data.

To design your sticker accurately, we'll need the following information.

1. Turret Diameter

Measure the diameter of your elevation turret using calipers. Please provide the measurement to the nearest 0.001 inch (one-thousandth of an inch). The more accurate your measurement, the more accurately we can space the click markings around the turret.

2. Turret Picture

Please provide a clear picture of your elevation turret. Photos help us identify the turret design, reference markings, and available space for your custom sticker.

3. Turret Specifications

This information is critical to accurately spacing your sticker's markings. We need to know how many clicks your turret has per rotation and the adjustment value of each click.

Many MIL scopes use 0.1 MIL per click, while MOA scopes commonly use 1/4 MOA or 1/8 MOA per click. These specifications vary by scope, so please verify the information engraved on your turret or provided in your scope's manual.

4. Sticker Height

Measure the usable height of the turret where the sticker will be applied, from the bottom of the turret to the top of the flat area below the knurled section. A clear side-view photo can also help us confirm the usable space.

5. Single-Tier or Dual-Tier Design

Single Tier

Displays yardage references on a single tier for a clean, straightforward layout.

Dual Tier

Features traditional MIL or MOA reference markings on the bottom tier and yardage indicators on the top tier.

6. Red Zone Markings

Would you like our optional red zone markings included on your sticker?

These markings highlight a range of click values around a calculated drop. For example, a calculated drop of 1.4 MIL at 400 yards could be shown with a dashed reference line at 1.4 MIL and a translucent red zone spanning 1.1 to 1.5 MIL.

The red zone provides a visual reference when conditions differ from those used to calculate your original drop data. Actual adjustments must be verified for your rifle, ammunition, and shooting environment.

7. Color Options

Our standard fill colors are white and gold, with black available for the top tier and markings. Looking for a different color combination? Contact us to discuss availability.

8. Custom Drop Data: 200–1,200 Yards

Provide your calculated drop values for the distances you want displayed, in MIL or MOA. Our custom stickers can accommodate your selected yardage references from 200 to 1,200 yards, depending on the design and available space.

Don't have your drop data yet? Contact us before ordering, and we can discuss the information needed to help determine appropriate values for your setup.